internet connectivity on build 5536

> Hi,
>
> Got a problem connecting to the internet on build 5536.
>
> Setup -
>
> 1 marvell yukon gigabit ethernet card
> 1 linksys router wrt54g
>
> the router firmware is at the current release.
>
> Tried using both the driver installed by vista and an updated diver from
> marvell (which didnt work at all).
>
> Symptons - 1. Can connect to my local network, and shared resources. Can
> connect to my routers set up page.
>
> 2. Can not connect to most internet sites. Error is dns server error. In
> some instances if I type in the ip address it will connect. But will not
> resolve the address any other way.
>
> I've tried the following -
> 1. disabled ipv6 protocol - same problem.
> 2. Tried entering in the configuration info for dns server, gateway etc in
> ipv4 and same problem.
> 3. Tried updating the card driver - lost all connections.
>
> Has anyone had a similar problem or know a workaround for this?
>
> This was not a problem in the beta 2 build.
>
> Thanks
>

>
> Apparent problem with Marvell adapters, got same trouble here
> "B Barley" wrote:
>

> > Hi,
> >
> > Got a problem connecting to the internet on build 5536.
> >
> > Setup -
> >
> > 1 marvell yukon gigabit ethernet card
> > 1 linksys router wrt54g
> >
> > the router firmware is at the current release.
> >
> > Tried using both the driver installed by vista and an updated diver from
> > marvell (which didnt work at all).
> >
> > Symptons - 1. Can connect to my local network, and shared resources. Can
> > connect to my routers set up page.
> >
> > 2. Can not connect to most internet sites. Error is dns server error. In
> > some instances if I type in the ip address it will connect. But will not
> > resolve the address any other way.
> >
> > I've tried the following -
> > 1. disabled ipv6 protocol - same problem.
> > 2. Tried entering in the configuration info for dns server, gateway etc in
> > ipv4 and same problem.
> > 3. Tried updating the card driver - lost all connections.
> >
> > Has anyone had a similar problem or know a workaround for this?
> >
> > This was not a problem in the beta 2 build.
> >
> > Thanks
> >

> I'm not so sure.
>
> I took the router out of the equation...
> disabled ipv6 and the link layer settings and got it working.
>
> "mittelk" wrote:
>

>>
>> Apparent problem with Marvell adapters, got same trouble here
>> "B Barley" wrote:
>>

>> > Hi,
>> >
>> > Got a problem connecting to the internet on build 5536.
>> >
>> > Setup -
>> >
>> > 1 marvell yukon gigabit ethernet card
>> > 1 linksys router wrt54g
>> >
>> > the router firmware is at the current release.
>> >
>> > Tried using both the driver installed by vista and an updated diver
>> > from
>> > marvell (which didnt work at all).
>> >
>> > Symptons - 1. Can connect to my local network, and shared resources.
>> > Can
>> > connect to my routers set up page.
>> >
>> > 2. Can not connect to most internet sites. Error is dns server error.
>> > In
>> > some instances if I type in the ip address it will connect. But will
>> > not
>> > resolve the address any other way.
>> >
>> > I've tried the following -
>> > 1. disabled ipv6 protocol - same problem.
>> > 2. Tried entering in the configuration info for dns server, gateway
>> > etc in
>> > ipv4 and same problem.
>> > 3. Tried updating the card driver - lost all connections.
>> >
>> > Has anyone had a similar problem or know a workaround for this?
>> >
>> > This was not a problem in the beta 2 build.
>> >
>> > Thanks
>> >

> FYI - found the same issue -- seem that there is a problem with the Marvell
> drivers... Did find a fix though as posted at:
> http://www.longhornblogs.com/chris12.../27/16677.aspx
>
> Disable IPv4 Checksum Offload and you should be good to go...
>
> At least worked for me
>
> "B Barley" <BBarley@discussions.microsoft.com> wrote in message
> news:7A7B2200-8A6A-4B6D-B385-6AE73BC65089@microsoft.com...

> > I'm not so sure.
> >
> > I took the router out of the equation...
> > disabled ipv6 and the link layer settings and got it working.
> >
> > "mittelk" wrote:
> >

> >>
> >> Apparent problem with Marvell adapters, got same trouble here
> >> "B Barley" wrote:
> >>
> >> > Hi,
> >> >
> >> > Got a problem connecting to the internet on build 5536.
> >> >
> >> > Setup -
> >> >
> >> > 1 marvell yukon gigabit ethernet card
> >> > 1 linksys router wrt54g
> >> >
> >> > the router firmware is at the current release.
> >> >
> >> > Tried using both the driver installed by vista and an updated diver
> >> > from
> >> > marvell (which didnt work at all).
> >> >
> >> > Symptons - 1. Can connect to my local network, and shared resources.
> >> > Can
> >> > connect to my routers set up page.
> >> >
> >> > 2. Can not connect to most internet sites. Error is dns server error.
> >> > In
> >> > some instances if I type in the ip address it will connect. But will
> >> > not
> >> > resolve the address any other way.
> >> >
> >> > I've tried the following -
> >> > 1. disabled ipv6 protocol - same problem.
> >> > 2. Tried entering in the configuration info for dns server, gateway
> >> > etc in
> >> > ipv4 and same problem.
> >> > 3. Tried updating the card driver - lost all connections.
> >> >
> >> > Has anyone had a similar problem or know a workaround for this?
> >> >
> >> > This was not a problem in the beta 2 build.
> >> >
> >> > Thanks
> >> >

>
>