Problems with Remote Based Solution; Not with IDE based Solution.

> Hi all,
>
> Any suggestions for this.
>
> Please help me.
>
> rangampalayam@rediffmail.com (Ranga) wrote in message

> > Hello all,
> >
> > I have a Via C3 Motherboard. For this, I Created a Firmware to boot
> > from a Remote Location.
> >
> > For this, FBA process got completed. After that I created a SDI image
> > and booted it from a Remote Location.
> >
> > After loading, (with the message splashing "Loading RAMDISK Image"),
> > the Login UI did not come up. Instead of that, the following error
> > message came up,

>
> -------------------------------------------------------------------------

> >
> > A problem has been detected and windows has been shut down to
> > prevent
> > damage to your computer
> >
> > A Kernel thread terminated while holding a Mutex.
> >
> > If this is the first time, you've seen this stop error screen,
> > restart
> > your computer. If this screen appears again, follow these steps:
> >
> > Check to make sure, any new hardware or software is properly
> > installed. If this is a new installation, ask your hardware or
> > software Manufacturer for any windows updates you might need.
> >
> > If problems continue, disable or remove any newly installed
> > hardware
> > or software. Disable BIOS Memory option such as caching or
> > shadowing. If
> > you need to use safe mode to remove or disable components,
> > restart your
> > computer, press f8 to select advanced startup options, and then
> > select safe mode.
> >
> > Technical Information:
> >
> > *** STOP: 0x 4000 008A (0x85D7 8860,0x85DB 7448,0x0000
> > 0000,0x0000 0000)
> > -------------------------------------------------------------------
> >
> >
> > The Remote Boot Image just terminated after this.
> >
> > Now, the Ran the Firmware from the IDE based Compact Flash. The
> > firmware works without any problems.
> >
> > I could find the problem only with the Remote boot based solution but
> > not in the Compact Flash based solution.
> >
> > Please help me regarding this.
> >
> > with regards,
> > Ranga.

> Ranga,
>
> Sounds like a driver is at fault in your configuration. It maybe a device
> driver specific to your hardware. It is possible that the problem is exposed
> only in a RAMDisk boot. Try the same steps to prepare an image for a
> different device. Try increasing the RAM. Let me know if the problem still
> repros
>
> --
> Thanks,
> - Saad, MS
>
> This posting is provided "AS IS" with no warranties, and confers no rights.
>
> "Ranga" <rangampalayam@rediffmail.com> wrote in message
> news:6e6631b7.0309040909.16887f35@posting.google.c om...

> > Hi all,
> >
> > Any suggestions for this.
> >
> > Please help me.
> >
> > rangampalayam@rediffmail.com (Ranga) wrote in message

> news:<6e6631b7.0309020842.6f9726c8@posting.google. com>...

> > > Hello all,
> > >
> > > I have a Via C3 Motherboard. For this, I Created a Firmware to boot
> > > from a Remote Location.
> > >
> > > For this, FBA process got completed. After that I created a SDI image
> > > and booted it from a Remote Location.
> > >
> > > After loading, (with the message splashing "Loading RAMDISK Image"),
> > > the Login UI did not come up. Instead of that, the following error
> > > message came up,

> >
> > -------------------------------------------------------------------------

> > >
> > > A problem has been detected and windows has been shut down to
> > > prevent
> > > damage to your computer
> > >
> > > A Kernel thread terminated while holding a Mutex.
> > >
> > > If this is the first time, you've seen this stop error screen,
> > > restart
> > > your computer. If this screen appears again, follow these steps:
> > >
> > > Check to make sure, any new hardware or software is properly
> > > installed. If this is a new installation, ask your hardware or
> > > software Manufacturer for any windows updates you might need.
> > >
> > > If problems continue, disable or remove any newly installed
> > > hardware
> > > or software. Disable BIOS Memory option such as caching or
> > > shadowing. If
> > > you need to use safe mode to remove or disable components,
> > > restart your
> > > computer, press f8 to select advanced startup options, and then
> > > select safe mode.
> > >
> > > Technical Information:
> > >
> > > *** STOP: 0x 4000 008A (0x85D7 8860,0x85DB 7448,0x0000
> > > 0000,0x0000 0000)
> > > -------------------------------------------------------------------
> > >
> > >
> > > The Remote Boot Image just terminated after this.
> > >
> > > Now, the Ran the Firmware from the IDE based Compact Flash. The
> > > firmware works without any problems.
> > >
> > > I could find the problem only with the Remote boot based solution but
> > > not in the Compact Flash based solution.
> > >
> > > Please help me regarding this.
> > >
> > > with regards,
> > > Ranga.